View PE4140G-06DFN_1294975.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Product Specification
PE4140
Product Description
The PE4140 is an ultra-high linearity passive broadband Quad MOSFET array with high dynamic range performance capable of operation beyond 6.0 GHz. This quad array operates with differential signals at all ports (RF, LO, IF), allowing mixers to be built that use LO powers from -7 dBm to +20 dBm. Typical applications range from frequency up/down-conversion to phase detection for Cellular/PCS Base Stations, Wireless Broadband Communications and STB/Cable modems. The PE4140 is manufactured on Peregrine's UltraCMOSTM process, a patented variation of silicon-on-insulator (SOI) technology on a sapphire substrate, offering the performance of GaAs with the economy and integration of conventional CMOS.
Ultra-High Linearity UltraCMOSTM Broadband Quad MOSFET Array
Features
* Ultimate Quad MOSFET array * Ultra-high linearity, broadband
performance beyond 6.0 GHz
* Ideal for mixer applications * Up/down conversion * Low conversion loss * High LO Isolation * Packaged in small 6-lead 3x3 mm DFN
Figure 1. Functional Diagram
Figure 2. Package Type
6-lead DFN
LO
IF
RF
Table 1. AC and DC Electrical Specifications @ +25 C
Symbol
FTYP VDS VDS Match VT R DS
Characteristics
Operating Frequency Range Drain-Source Voltage Drain-Source Voltage Match Threshold Voltage Drain-Source `ON' Resistance
1
Test Conditions
Min
DC
Typ
Max
6.0
Units
GHz mV mV mV
VGS = +3V, IDS = 40 mA
260
320 12
380 40
VDS = 0.1V; per ASTM F617-00 VGS = +3V, IDS = 40 mA 6.5
-100 7.75 9.5
Note 1: Typical untested operating frequency range of Quad MOSFET transistors.
Document No. 70-0089-05 www.psemi.com
(c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 10
PE4140
Product Specification
Figure 3. Pin Configuration (Top View)
Electrostatic Discharge (ESD) Precautions This MOSFET device has minimally protected inputs and is highly susceptible to ESD damage. When handling this UltraCMOSTM device, observe the same precautions that you would use with other ESD-sensitive devices. Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOSTM devices are immune to latch-up. Device Description
IF1 RF1 RF2
1 2 3
Exposed Solder Pad
(bottom side)
6 5 4
IF2 LO1
LO2
Table 2. Pin Descriptions
Pin No.
1 2 3 4 5 6
Pin Name
IF1 RF1 RF2 LO2 LO1 IF2
Description
IF Output Connection (Drain) RF Input Connection (Source) RF Input Connection (Source) LO Input Connection (Gate) LO Input Connection (Gate) IF Output Connection (Drain)
The PE4140 passive broadband Quad MOSFET array is designed for use in up-conversion and down-conversion applications for high performance systems such as cellular infrastructure equipment and STB/CATV systems. The PE4140 is an ideal mixer core for a wide range of mixer products, including module level solutions that incorporate baluns or other singleended matching structures enabling three-port operation. The performance level of this passive mixer is made possible by the very high linearity afforded by Peregrine's UltraCMOSTM process.
Units
C C
Table 3. Absolute Maximum Ratings
Symbol
TST TOP VDC + AC
Parameters/ Conditions
Storage temperature range Operating temperature range Maximum DC plus peak AC voltage across DrainSource Maximum DC plus peak AC voltage across GateDrain or Gate-Source ESD Sensitive Device
Min
-65 -40
Max
150 85
Marking Packaged devices are marked with part number "4140", date code and lot code.
3.3
V
VDC+AC VESD
4.2 250
V V
Absolute Maximum Ratings are those values listed in the above table. Exceeding these values may cause permanent device damage. Functional operation should be restricted to the limits in the DC Electrical Specifications table. Exposure to absolute maximum ratings for extended periods may affect device reliability.
(c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 10
Document No. 70-0089-05 UltraCMOSTM RFIC Solutions
PE4140
Product Specification
Evaluation Kit
Figure 4. Evaluation Board Layout
Peregrine Specification 101/0090
Applications Support
If you have a problem with your evaluation kit or if you have applications questions, please contact applications support: E-Mail: help@psemi.com (fastest response) Phone: (858) 731-9400
Figure 5. Evaluation Board Schematic
Peregrine Specification 102/0115
Note:
This is the complete evaluation board schematic; which can be used for multiple configurations. Not all components need be populated. Refer to 'typical schematics' on following pages.
Document No. 70-0089-05 www.psemi.com
(c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 10
PE4140
Product Specification
Figure 6. Typical Schematic for a PCS Application
J3 LO Input
T1 M/A Com ETC1.6-4-2-3 4 5 3 2 1
R2 1.2 nH
R3 2.7 nH 4 5 PE4140 6 R8 2.7 nH 2 3 4 1 3 2 1
T2 M/A Com ETC1.6-4-2-3 1 5 2 3 4
R16 3 pF
J4 RF Input
R12 1.2 nH
5
T3 TOKO 617DB-1024
J6 IF Out
Table 4. Typical Performance in a PCS Application @ +25 C
Parameter
Frequency Range** LO RF IF Conversion Loss** (Includes balun losses) Isolation** LO-RF LO-IF Input IP3** Input 1 dB Compression** 36 26 32 22 dB dB dBm dBm 1630 1700 --70 8.5 2130 2200 MHz MHz MHz dB
Minimum
Typical
Maximum
Units
** Data taken on an Evaluation Board narrow-band tuned to cover the PCS band, IF = 73MHz low-side, LO drive = 17dBm.
(c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 10
Document No. 70-0089-05 UltraCMOSTM RFIC Solutions
PE4140
Product Specification
Typical Performance Plots in a PCS Application @ +25 C (LO=17 dBm, IF=73 MHz Low-side) Figure 7. IIP3 vs. Frequency Figure 8. Conversion Loss vs. Frequency
40 35 30 IIP3 (dBm) @ 17dBm Lo 25 20 15 10 5 0 1700 Conversion Loss (dB) @ 17dBm Lo IF=73Mhz Low-side
10
9
8 Conversion Loss 7
6
1750
1800
1850
1900
1950
2000
2050
2100
5 1700
1750
1800
1850
1900
1950
2000
2050
2100
Frequency (MHz)
Frequency (MHz)
Figure 9. LO-RF & LO-IF Isolation
0 -5 -10 -15 -20 -25 LO-RF -30 -35 -40 1700 LO-IF
Isolation (dB)
1750
1800
1850
1900
1950
2000
2050
2100
Frequency (MHz)
Document No. 70-0089-05 www.psemi.com
(c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 5 of 10
PE4140
Product Specification
Figure 10. Typical Schematic for a CATV Application
(Reference Designators Refer to locations on Evaluation Board: 101/0090) 4.7nH L1 U1 4 5 6 MLP6-3X3 L2 4.7nH 3 2 1 ETC1.6-4-2-3 T 2 1 5 2 RF Input 3 4 R16 3.0pF 1
J3 LO Input 1
ETC1.6-4-2-3 4 T1 3 2 5 1
J4
3
2
1 (Cut short between pads)
4
5
T3 ETC1-1-13
1
J6 IF Out
Note: L1 and L2 provide LO port matching for optimum performance. Typical gate capacitance is approximately 2.5 pF.
Table 5. Typical Performance in a CATV Application @ +25 C
Parameter
Frequency Range** LO RF IF Conversion Loss** (Includes balun losses) Isolation** LO-RF LO-IF Input IP3** Input 1 dB Compression** 1116 54 --1062 6.5 1926 864 MHz MHz MHz dB
Minimum
Typical
Maximum
Units
40 28 23 13
dB dB dBm dBm
** Data taken on an Evaluation Board tuned for a broadband CATV application, IF = 1062 MHz, RF drive = -5 dBm, LO drive = 10 dBm.
(c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 6 of 10
Document No. 70-0089-05 UltraCMOSTM RFIC Solutions
PE4140
Product Specification
Typical Performance Plots in a CATV Application @ +25 C Figure 11. IIP3 vs. Frequency Figure 12. Conversion Loss vs. Frequency
30
10
25
Conversion Loss (dB) @10dBm LO
8
IIP3 (dBm) @10dBm LO
20
6
15
4
10
5
2
0 0 200 400 600 800 1000
0 0 200 400 600 800 1000
Frequency (MHz)
Frequency (MHz)
Figure 13. LO-RF & LO-IF Isolation
0
-10
-20 Isolation (dB) LO-IF -30
-40
-50
LO-RF
-60 1000
1200
1400
1600
1800
2000
Frequency (MHz)
Document No. 70-0089-05 www.psemi.com
(c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 7 of 10
PE4140
Product Specification
Figure 14. Package Drawing
6-lead DFN
3.00 C L -A-B4
6 0.125
5
C L PIN MAR 1 K 0.10 C 1 4 0.10 C 2 3
3.00
4
0.125
10+2 -10 0.100 C
TOP VIEW
DETAIL C 0.025 0.025
0.90 0.10 0.080 C 3 0.0250.025 SIDE VIEW SEE DETAIL B
0.70 0.05 0.20 0.05 SEATING PLANE -CDETAIL B
C L 0.95 EXPOSED PAD 1 2 3
0.35
+0.08 -0.02 0.10 0.05 C
0.17 MIN. CAB 0.29 +0.21 -0.08 EXPOSED SLUG/ HEAT SINK 0.24 +0.20 -0.08 0.125 0.17 0.30
SEE DETAIL A R 0.15 TYP
R0.127 TYP 1.21 0.10 0.605 0.05 THIS FEATURE APPLIES TO BOTH ENDS OF THE PKG. DETAIL A EXPOSED METALIZED FEATURE EDGE OF PLASTIC BODY
EXPOSED (2X)
6
5
4
3 1.050.05 2.010.10
.20 MIN.
BOTTOM VIEW 1. DIMENSIONS AND TOLERANCES ARE PER ANSi Y14.5 2. DIMENSIONS ARE IN MILLIMETERS, ANGLES ARE IN DEGREES. 3 4 COPLANARITY APPLIES TO EXPOSED HEAT SLUG AS WELL AS THE TERMINALS. PROFILE TOLERANCE APPLIES TO PLASTIC BODY ONLY.
(c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 8 of 10
Document No. 70-0089-05 UltraCMOSTM RFIC Solutions
PE4140
Product Specification
Figure 15. Tape and Reel Specifications
6-lead DFN
Table 6. Dimensions
Dimension
Ao Bo Ko P W T R7 Quantity R13 Quantity
DFN 3x3 mm
3.23 0.1 3.17 0.1 1.37 0.1 4 0.1 8 +0.3, -0.1 0.254 0.02 3000 N.A.
Note: R7 = 7 inch Lock Reel, R13 = 13 inch Lock Reel
Table 7. Ordering Information
Order Code
4140-01 4140-02 4140-00 4140-51 4140-52
Part Marking
4140 4140 PE4140-EK 4140 4140
Description
PE4140-06DFN 3x3mm-12800F PE4140-06DFN 3x3mm-3000C PE4140-06DFN 3x3mm-EK PE4140G-06DFN 3x3mm-12800F PE4140G-06DFN 3x3mm-3000C
Package
6-lead 3x3 mm DFN 6-lead 3x3 mm DFN Evaluation Kit Green 6-lead 3x3 mm DFN Green 6-lead 3x3 mm DFN
Shipping Method
12800 units / Canister 3000 units / T&R 1 / Box 12800 units / Canister 3000 units / T&R
Document No. 70-0089-05 www.psemi.com
(c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 9 of 10
PE4140
Product Specification
Sales Offices
The Americas Peregrine Semiconductor Corp.
9450 Carroll Park Drive San Diego, CA 92121 Tel 858-731-9400 Fax 858-731-9499
North Asia Pacific Peregrine Semiconductor K.K.
5A-5, 5F Imperial Tower 1-1-1 Uchisaiwaicho, Chiyoda-ku Tokyo 100-0011 Japan Tel: +81-3-3502-5211 Fax: +81-3-3502-5213
Europe Peregrine Semiconductor Europe
Commercial Products: Batiment Maine 13-15 rue des Quatre Vents F- 92380 Garches, France Tel: +33-1-47-41-91-73 Fax : +33-1-47-41-91-73 Space and Defense Products: 180 Rue Jean de Guiramand 13852 Aix-En-Provence cedex 3, France Tel: +33(0) 4 4239 3361 Fax: +33(0) 4 4239 7227
South Asia Pacific Peregrine Semiconductor
28G, Times Square, No. 500 Zhangyang Road, Shanghai, 200122, P.R. China Tel: +86-21-5836-8276 Fax: +86-21-5836-7652
For a list of representatives in your area, please refer to our Web site at: www.psemi.com
Data Sheet Identification
Advance Information
The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user's own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine's products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS is a trademark of Peregrine Semiconductor Corp.
Preliminary Specification
The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product.
Product Specification
The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a DCN (Document Change Notice).
(c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 10 of 10
Document No. 70-0089-05 UltraCMOSTM RFIC Solutions

▲Up To Search▲

Price & Availability of PE4140G-06DFN

	To Download PE4140G-06DFN Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .